632
edits
Changes
Jump to navigation
Jump to search
Line 1:
Line 1: + + − <br />+ − − == Microflush Half Gallon Toilets == − Model LF-220 DC Operated − − Model LF-220 Downward Discharge (All dimensions +/- 0.5") − Installation/Service Manual P/N 24155+ − − − 452 East Hill Road, Willits, CA 95490 USA − − ''Tel: 707.459.5563 Tel: 800.358.8280 Fax: 707.459.6617'' − − ''www.microphor.com www.wabtec.com'' − − − '''Thank You!''' − − Thank you for purchasing a Microphor product. Please read this manual completely prior to installation of your Microflush® toilet. Microphor General Terms and Condi- tions Covering Sales apply. − <br /> − − == Customer Service == Line 65:
Line 47: + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + Line 70:
Line 83: − <br /> − Line 80:
Line 91: − <br /> − == Water Connection ==+ Line 88:
Line 98: + + + + − + − The normal water level is factory pre- set to the top of the Flapper.+ + + + + + + + + + + + + + +
no edit summary
Microflush Half Gallon Toilets
Model LF-220 | DC Operated
[http://wanderlodge.wiki/images/8/88/Microphor_Manual-_LF-220_DC_prior_to_2005.pdf Installation/Service Manual: P/N 24155]
= Customer Service =
If you have any questions concerning your Microphor product, please contact us:
If you have any questions concerning your Microphor product, please contact us:
2. After the Flapper has closed, fresh water continues to enter the bowl to a predetermined level until the Timer closes the solenoid valve. An adjustment on the Timer allows adjustment of the water level in the bowl to compensate for water pressure fluctuations. A vacuum breaker is provided as an anti-siphon device.
2. After the Flapper has closed, fresh water continues to enter the bowl to a predetermined level until the Timer closes the solenoid valve. An adjustment on the Timer allows adjustment of the water level in the bowl to compensate for water pressure fluctuations. A vacuum breaker is provided as an anti-siphon device.
=== Flush Cycle ===
[[File:Microphor LF-220 Flush Cycle.png|left|frameless|856x856px]]
=== Model LF-220 Downward Discharge (All dimensions +/- 0.5") ===
[[File:Microphor LF-220 Downward Discharge Diagram.png|left|frameless|1049x1049px]]
<br />
= Installation =
= Installation =
Note: This toilet is a drop-thru unit. No horizontal waste line runs may be utilized. Contact the factory for specific application data.
Note: This toilet is a drop-thru unit. No horizontal waste line runs may be utilized. Contact the factory for specific application data.
= Mounting Toilet =
= Mounting Toilet =
Turn toilet upside-down and place enclosed Wax Ring (P/N 27208), onto the bottom of mouting flange of the toilet hopper. Carefully turn toilet right-side up and place over the center of a standard floor discharge flange. Press toilet down firmly and evenly to form a seal between the wax ring and the floor flange. Mount the toilet to the floor with the four Closet Screws and install Bolt Caps over the closet screws (both provided).
Turn toilet upside-down and place enclosed Wax Ring (P/N 27208), onto the bottom of mouting flange of the toilet hopper. Carefully turn toilet right-side up and place over the center of a standard floor discharge flange. Press toilet down firmly and evenly to form a seal between the wax ring and the floor flange. Mount the toilet to the floor with the four Closet Screws and install Bolt Caps over the closet screws (both provided).
= Electrical Connection =
= Electrical Connection =
.25” spade connector near the Timer and Thermal Circuit Breaker: red wire to positive (+), black wire to negative (-).
.25” spade connector near the Timer and Thermal Circuit Breaker: red wire to positive (+), black wire to negative (-).
= Water Connection =
See Rough-In Dimensions.
See Rough-In Dimensions.
'''Ideal water pressure is 35 PSI at the toilet.''' Be sure water lines are free of debris before connecting water supply to toilet. Water supply to the toilet is to be 1/2” OD plumbed directly to the toilet. Do not install filter(s) in the toilet water supply line.
'''Ideal water pressure is 35 PSI at the toilet.''' Be sure water lines are free of debris before connecting water supply to toilet. Water supply to the toilet is to be 1/2” OD plumbed directly to the toilet. Do not install filter(s) in the toilet water supply line.
= Water Level =
[[File:Microphor Water Level Diagram.png|thumb|Water Level]]
The normal water level is factory pre- set to the top of the Flapper.
<br />
<br />
== '''Water Level''' ==
= Water Level Adjustment =
[[File:Microphor Water Level Adjustment .png|thumb|Water Level Adjustment]]
Locate the timer on the bracker under the china lid. Turn Timer adjustment knob clockwise to increase water level, and counterclockwise to decrease. Do not turn past stops.
<br />
= Seat Installation =
Place the seat over the bowl opening, so that the mounting hinges on the seat align with the two holes in the bowl just behind the bowl opening. Insert the two seat mounting screws provided with the seat into the hinges’ holes and mounting holes in the bowl, from the top. Install washers and mounting nuts provided with the seat, from under- neath, and tighten firmly. Install screw head cover tabs or other hardware provided with the seat, per seat manufacturer’s instructions.
<br />
= Maintenance =
If the toilet is to be out of service for a period of time, spray 100% silicone on the flapper seal when the flapper is open to prevent if from becoming dry.
<br />
= Winterizing =
Shut OFF water to toilet. Flush toilet three times or until water no longer flows into the bowl. Unhook water supply at angle stop. Empty water in line into receptacle.
<br />